Thursday 9 December 2010

Water recycling top of the agenda for washing plant operators

The inclusion of water recycling equipment on washing plant installations has risen dramatically in recent times as operators realise that in addition to the altruistic benefit of protecting the world’s most precious natural resource there are significant efficiency gains to be enjoyed.


The specification of equipment such as thickeners and filter presses has seemingly progressed from being seen as something that was done only at the behest of planning authorities. As awareness has grown of the real potential for these water recycling technologies to improve the efficiency of traditional quarrying and C&D waste recycling processes their introduction to existing operations and new installations has increased dramatically.

As recently as three or four years ago a thickener or filter press was only specified on around 20% of our washing plant installations. The last 12 months has seen this figure rise to around 80%.

This increase is not restricted to any specific geographical area with recent installations in Ireland, the UK, Europe, Middle East, Australia, South America and South Africa.

The key drivers behind the increased specification of this equipment differ from one installation to the next and include issues concerning:

  1. The space available on site to accommodate large settling ponds
  2. The availability of the volumes of water required to operate a new washing plant
  3. Reducing health and safety risks on site
  4. Efficiency improvements offered through significantly reduced operational costs.

We have focused on the potential efficiency gains for a number of years now when in discussion with both new and existing clients. The management of large settling ponds is a very expensive process and one which the introduction of a thickener can significantly reduce. If the full sludge management system including a filter press is specified these settling ponds can be removed completely from site.

In the UK market the specification of water recycling equipment has been most prevalent on construction and demolition waste recycling operations due to the nature of the sites where these plants are located. While it is usually the case that traditional sand and gravel or hard rock quarries are located in rural settings on large sites, the opposite is the case for recycling plants.


The nature of the material being processed means these sites are located in urban areas and as a result some degree of water recycling is essential on all of our C&D waste recycling plants. We have many plants working on sites located in built up industrial and residential areas where not only is there not the space to contemplate settling ponds but the health and safety issues surrounding these ponds rule them out of consideration at the very outset.

Outside the recycling sector the demand for equipment is coming from operators who are introducing a washing plant for the first time. Operators considering a washing plant on a site that has previously only operated a dry crushing and screening process are more focused on the volume of water required to run the plant than those already operating washing plants.

The issue of the space required for ponds is more acute for those not already operating these ponds and one of the first things they are concerned with is reducing this space requirement. The specification of a thickener and filter press is the obvious way to achieve this.

It is not exclusively the ponds issue that leads operators to specify some sort of water recycling system however. An equally pressing issue is gaining access to the volumes of fresh water required to run the washing plant should a thickener not be included.

On a recently completed project in Poland this was precisely the issue that the customer was faced with. Our customer was operating an Evowash sand washing plant after their dry screening process but had a requirement to increase sand production following the award of a new contract.

The customer chose our M2500 mobile washing plant to deliver this increased capacity but they simply did not have access to the volumes of water required to run the new plant. The introduction of an Aquacycle thickener on this upgraded washing plant ensured that the customer in this instance was able to take advantage of the increased sand and aggregate production capacity while requiring less water to do so. The introduction of the thickener on its own has allowed the customer to recycle between 85% and 90% of the water used to feed the washing plant.


It is rarely the case that operators will only have one of these issues to deal with and according to CDE it is usually a combination of factors working together that lead to the conclusion that a thickener and / or filter press is needed. In the case of a recent project in South Africa the customer had a number of concerns.

Firstly, they were spending considerable time and money cleaning out their existing ponds and reprocessing material due to the inefficiency of their existing sand washing plant so the first priority for them was more efficient sand washing. They were also adamant that they wanted to address their ponds issue and reduce not only the space they were occupying but the cost of managing them.

While thickeners are much used in the mining sector in South Africa it is believed that this is the first instance of a thickener system being installed on a traditional quarrying operation. A further consideration for this customer was the location of the washing plant adjacent to a local river. With this at the forefront of the customers’ mind the safe storage of waste material from the washing plant was of paramount importance.

We fully expect this trend towards thickeners and filter presses to continue. Given the fact that this year has seen the installation of our first water recycling systems in six new countries the expectation is that this will lead to more in the coming months and years.

No comments:

Post a Comment